This is a fantastic product and it is VERY good looking. It displays RGB colors in the fans and inside the cooler itself. It has a “tunnel” down the middle which shows a holographic light effect. There is a small controller to set the lighting mode. It is attached to a metal surface inside your case with an internal magnet. Many lighting modes including a “temperature-gauge” mode that changes with processor temp (load). The mode can be set using:
a) the buttons on this small controller
b) by connecting the controller to a 9-pin USB header on the motherboard then using their free software
(“USB Male to 5 Pin Motherboard Female Header Adapter Cable” required)
c) By connecting cooler to an RGB-enabled motherboard
The unit is nearly silent at low CPU loads/temps and quiet even at full speed. It provides airflow over the DRAM sticks, with the air flowing from the front of the case to the rear. It requires a high clearance above the motherboard, so you need to have an appropriate, “deep” case. It is a tight fit next to the DRAM sticks, but it is obviously engineered to be that way.
It is not an easy installation, but it is very doable with the patience to follow the steps, which are provided in a “picture only” instruction pamphlet (less translation with no words). Access to the back of the motherboard at the site of the processor is required so if your case doesn’t have that access, you will need to remove the motherboard.
There is a tiny wrench included to tighten the cooler to the mounts on the motherboard, but I found it impossible to access the screws from the sides, as the instructions show. Instead, I removed the two fans from the cooler which gave me straight-on access and allowed me to easily tighten the screws with a screwdriver, from above. Each fan is attached with 4 knurled screws which can be removed and reinstalled with your fingers. This too was obviously engineered that way, it’s just too bad that the instructions don’t mention that feature or that method of installation. It would have saved me hours.
The kit contains a TINY tube of thermal compound paste, which you should throw away and, instead, buy a tube of real paste with 4 grams of compound. The contact pad has four, double-ended heat pipes which go up and through the cooler and I am sure that heat conduction, away from the processor, is as good as it gets. So much more than the Intel cooler that came with my chip.
There is one glaring problem. There is no support available. I searched their website and could not find any way to contact Cooler Master other than to request that a service ticket be opened. I did that and never heard anything back from them. Amazon offers "support" on the pages from which I ordered but they could only offer to transfer me to Cooler Master. I got an 800 number from them, which I later found on their website, but always got a VM that stated their hours and said they were too busy to answer the phone and then it hung up. I tried for days at different times of the day and NEVER got them to answer. All I wanted to do was find out if my motherboard was supported and if they had any more installation suggestions. Luckily I figured it out myself and removed the fans as I stated earlier.
All-in-all, I am extremely pleased with this cooler and I feel that the price would be reasonable even if it were doubled. It is a very good-looking addition to my setup – see my attached pictures. BTW: I purchased the $9.99 Protection Plan which would probably be a good idea for anyone else.
Enjoy fast, free delivery, exclusive deals, and award-winning movies & TV shows with Prime
Try Prime
and start saving today with fast, free delivery
Similar item to consider
Frequently bought together
$89.00
Get it as soon as Sunday, May 19
Only 1 left in stock - order soon.
Total price:
To see our price, add these items to your cart.
Choose items to buy together.
Featured items you may like
Page 1 of 1 Start overPage 1 of 1
Videos
Page 1 of 1Start OverPage 1 of 1
Videos for this product
0:54
Click to play video
Cooler Master MasterAir MA410M
Cooler Master
Reviews with images
Fantastic cooler at a great price
This is a fantastic product and it is VERY good looking. It displays RGB colors in the fans and inside the cooler itself. It has a “tunnel” down the middle which shows a holographic light effect. There is a small controller to set the lighting mode. It is attached to a metal surface inside your case with an internal magnet. Many lighting modes including a “temperature-gauge” mode that changes with processor temp (load). The mode can be set using:a) the buttons on this small controllerb) by connecting the controller to a 9-pin USB header on the motherboard then using their free software (“USB Male to 5 Pin Motherboard Female Header Adapter Cable” required)c) By connecting cooler to an RGB-enabled motherboardThe unit is nearly silent at low CPU loads/temps and quiet even at full speed. It provides airflow over the DRAM sticks, with the air flowing from the front of the case to the rear. It requires a high clearance above the motherboard, so you need to have an appropriate, “deep” case. It is a tight fit next to the DRAM sticks, but it is obviously engineered to be that way.It is not an easy installation, but it is very doable with the patience to follow the steps, which are provided in a “picture only” instruction pamphlet (less translation with no words). Access to the back of the motherboard at the site of the processor is required so if your case doesn’t have that access, you will need to remove the motherboard.There is a tiny wrench included to tighten the cooler to the mounts on the motherboard, but I found it impossible to access the screws from the sides, as the instructions show. Instead, I removed the two fans from the cooler which gave me straight-on access and allowed me to easily tighten the screws with a screwdriver, from above. Each fan is attached with 4 knurled screws which can be removed and reinstalled with your fingers. This too was obviously engineered that way, it’s just too bad that the instructions don’t mention that feature or that method of installation. It would have saved me hours.The kit contains a TINY tube of thermal compound paste, which you should throw away and, instead, buy a tube of real paste with 4 grams of compound. The contact pad has four, double-ended heat pipes which go up and through the cooler and I am sure that heat conduction, away from the processor, is as good as it gets. So much more than the Intel cooler that came with my chip.There is one glaring problem. There is no support available. I searched their website and could not find any way to contact Cooler Master other than to request that a service ticket be opened. I did that and never heard anything back from them. Amazon offers "support" on the pages from which I ordered but they could only offer to transfer me to Cooler Master. I got an 800 number from them, which I later found on their website, but always got a VM that stated their hours and said they were too busy to answer the phone and then it hung up. I tried for days at different times of the day and NEVER got them to answer. All I wanted to do was find out if my motherboard was supported and if they had any more installation suggestions. Luckily I figured it out myself and removed the fans as I stated earlier.All-in-all, I am extremely pleased with this cooler and I feel that the price would be reasonable even if it were doubled. It is a very good-looking addition to my setup – see my attached pictures. BTW: I purchased the $9.99 Protection Plan which would probably be a good idea for anyone else.
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
Reviewed in the United States on July 21, 2019
Color: MA410M ARGBStyle: 4 HeatPipesVerified Purchase
This is a fantastic product and it is VERY good looking. It displays RGB colors in the fans and inside the cooler itself. It has a “tunnel” down the middle which shows a holographic light effect. There is a small controller to set the lighting mode. It is attached to a metal surface inside your case with an internal magnet. Many lighting modes including a “temperature-gauge” mode that changes with processor temp (load). The mode can be set using:
a) the buttons on this small controller
b) by connecting the controller to a 9-pin USB header on the motherboard then using their free software
(“USB Male to 5 Pin Motherboard Female Header Adapter Cable” required)
c) By connecting cooler to an RGB-enabled motherboard
The unit is nearly silent at low CPU loads/temps and quiet even at full speed. It provides airflow over the DRAM sticks, with the air flowing from the front of the case to the rear. It requires a high clearance above the motherboard, so you need to have an appropriate, “deep” case. It is a tight fit next to the DRAM sticks, but it is obviously engineered to be that way.
It is not an easy installation, but it is very doable with the patience to follow the steps, which are provided in a “picture only” instruction pamphlet (less translation with no words). Access to the back of the motherboard at the site of the processor is required so if your case doesn’t have that access, you will need to remove the motherboard.
There is a tiny wrench included to tighten the cooler to the mounts on the motherboard, but I found it impossible to access the screws from the sides, as the instructions show. Instead, I removed the two fans from the cooler which gave me straight-on access and allowed me to easily tighten the screws with a screwdriver, from above. Each fan is attached with 4 knurled screws which can be removed and reinstalled with your fingers. This too was obviously engineered that way, it’s just too bad that the instructions don’t mention that feature or that method of installation. It would have saved me hours.
The kit contains a TINY tube of thermal compound paste, which you should throw away and, instead, buy a tube of real paste with 4 grams of compound. The contact pad has four, double-ended heat pipes which go up and through the cooler and I am sure that heat conduction, away from the processor, is as good as it gets. So much more than the Intel cooler that came with my chip.
There is one glaring problem. There is no support available. I searched their website and could not find any way to contact Cooler Master other than to request that a service ticket be opened. I did that and never heard anything back from them. Amazon offers "support" on the pages from which I ordered but they could only offer to transfer me to Cooler Master. I got an 800 number from them, which I later found on their website, but always got a VM that stated their hours and said they were too busy to answer the phone and then it hung up. I tried for days at different times of the day and NEVER got them to answer. All I wanted to do was find out if my motherboard was supported and if they had any more installation suggestions. Luckily I figured it out myself and removed the fans as I stated earlier.
All-in-all, I am extremely pleased with this cooler and I feel that the price would be reasonable even if it were doubled. It is a very good-looking addition to my setup – see my attached pictures. BTW: I purchased the $9.99 Protection Plan which would probably be a good idea for anyone else.
a) the buttons on this small controller
b) by connecting the controller to a 9-pin USB header on the motherboard then using their free software
(“USB Male to 5 Pin Motherboard Female Header Adapter Cable” required)
c) By connecting cooler to an RGB-enabled motherboard
The unit is nearly silent at low CPU loads/temps and quiet even at full speed. It provides airflow over the DRAM sticks, with the air flowing from the front of the case to the rear. It requires a high clearance above the motherboard, so you need to have an appropriate, “deep” case. It is a tight fit next to the DRAM sticks, but it is obviously engineered to be that way.
It is not an easy installation, but it is very doable with the patience to follow the steps, which are provided in a “picture only” instruction pamphlet (less translation with no words). Access to the back of the motherboard at the site of the processor is required so if your case doesn’t have that access, you will need to remove the motherboard.
There is a tiny wrench included to tighten the cooler to the mounts on the motherboard, but I found it impossible to access the screws from the sides, as the instructions show. Instead, I removed the two fans from the cooler which gave me straight-on access and allowed me to easily tighten the screws with a screwdriver, from above. Each fan is attached with 4 knurled screws which can be removed and reinstalled with your fingers. This too was obviously engineered that way, it’s just too bad that the instructions don’t mention that feature or that method of installation. It would have saved me hours.
The kit contains a TINY tube of thermal compound paste, which you should throw away and, instead, buy a tube of real paste with 4 grams of compound. The contact pad has four, double-ended heat pipes which go up and through the cooler and I am sure that heat conduction, away from the processor, is as good as it gets. So much more than the Intel cooler that came with my chip.
There is one glaring problem. There is no support available. I searched their website and could not find any way to contact Cooler Master other than to request that a service ticket be opened. I did that and never heard anything back from them. Amazon offers "support" on the pages from which I ordered but they could only offer to transfer me to Cooler Master. I got an 800 number from them, which I later found on their website, but always got a VM that stated their hours and said they were too busy to answer the phone and then it hung up. I tried for days at different times of the day and NEVER got them to answer. All I wanted to do was find out if my motherboard was supported and if they had any more installation suggestions. Luckily I figured it out myself and removed the fans as I stated earlier.
All-in-all, I am extremely pleased with this cooler and I feel that the price would be reasonable even if it were doubled. It is a very good-looking addition to my setup – see my attached pictures. BTW: I purchased the $9.99 Protection Plan which would probably be a good idea for anyone else.
Images in this review
Reviewed in the United States on December 6, 2018
Color: MA410M ARGBStyle: 4 HeatPipesVerified Purchase
This cooler has been in my build for 3 months now from 09/18 - 12/18 (today), and it's still running well.
Things to look out for:
1) Make sure you have room. It is a large cooler that almost touches the glass of my case. I had to move my ram to accommodate this cooler. (My ram sticks are admittedly really tall..)
2) The mounting brackets align when the thumbscrews are tightened in a criss-cross order. I had to unmount it the first time because I did the lazy thing and tightened them clockwise. (The last thumbscrew did not align because I was lazy)
3) The lights are ARGB, not RGB. The plugs are different. I did not notice this when I ordered it, but thankfully the included ARGB controller worked for me, so I did not have to return it.
4) The instructions are more pictures than words. I didn't run into any problems, but I see how some of the pictures may be confusing.
5) The fans are not dead silent. There is a gentle hum, especially when gaming. I don't find this distracting, but if you need a totally silent cooler, then there are other options for silent air coolers, such as a noctua.
For the price I paid (just shy of $60), I'm happy with this cooler's performance and looks.
Things to look out for:
1) Make sure you have room. It is a large cooler that almost touches the glass of my case. I had to move my ram to accommodate this cooler. (My ram sticks are admittedly really tall..)
2) The mounting brackets align when the thumbscrews are tightened in a criss-cross order. I had to unmount it the first time because I did the lazy thing and tightened them clockwise. (The last thumbscrew did not align because I was lazy)
3) The lights are ARGB, not RGB. The plugs are different. I did not notice this when I ordered it, but thankfully the included ARGB controller worked for me, so I did not have to return it.
4) The instructions are more pictures than words. I didn't run into any problems, but I see how some of the pictures may be confusing.
5) The fans are not dead silent. There is a gentle hum, especially when gaming. I don't find this distracting, but if you need a totally silent cooler, then there are other options for silent air coolers, such as a noctua.
For the price I paid (just shy of $60), I'm happy with this cooler's performance and looks.
Images in this review
Reviewed in the United States on February 13, 2021
Color: MA410M ARGBStyle: 4 HeatPipesVerified Purchase
Reviewed in the United States on February 11, 2019
The looks of the cooler are pretty great, I like the temperature indication LED mode. The black shroud around the fins was annoying to deal with during installation, but it gives the cooler a very clean look once it's installed so It's worth it.
The cooler itself was somewhat of a pain to install. The included wrench was intended for you to be able to install it with the fans on, but it's practically impossible to do while the motherboard is installed in your case. I didn't want to remove my motherboard so I removed the fans from the cooler and was able to install the cooler with a screw driver instead of the included wrench. You'll just need to be careful to not damage the fins if you do it that way but I found it to be much easier in the end, and reinstalling the fans was relatively easy if you have a short or 90 degree screwdriver. Depending on your case your mileage may vary. I have a Fractal Design Define R4.
Overall I'm happy with the look and performance. I didn't have a lot of extra headroom on my power supply for an All in One water cooler, and this seems to do the job just as well with air.
Color: MA410M ARGBStyle: 4 HeatPipesVerified Purchase
Lowered the temps of my Ryzen 5 2600X by almost 20 degrees C
Reviewed in the United States on February 11, 2019
During Handbrake encodes of 1080p video my processor would constantly post temps above 80 C. I'm encoding a video right now and I'm only hitting 66 C at the highest.Reviewed in the United States on February 11, 2019
The looks of the cooler are pretty great, I like the temperature indication LED mode. The black shroud around the fins was annoying to deal with during installation, but it gives the cooler a very clean look once it's installed so It's worth it.
The cooler itself was somewhat of a pain to install. The included wrench was intended for you to be able to install it with the fans on, but it's practically impossible to do while the motherboard is installed in your case. I didn't want to remove my motherboard so I removed the fans from the cooler and was able to install the cooler with a screw driver instead of the included wrench. You'll just need to be careful to not damage the fins if you do it that way but I found it to be much easier in the end, and reinstalling the fans was relatively easy if you have a short or 90 degree screwdriver. Depending on your case your mileage may vary. I have a Fractal Design Define R4.
Overall I'm happy with the look and performance. I didn't have a lot of extra headroom on my power supply for an All in One water cooler, and this seems to do the job just as well with air.
Images in this review
Top reviews from other countries
laurent constantin
super beau
Reviewed in France on August 9, 2023Color: MA410M ARGBStyle: 4 HeatPipesVerified Purchase
Grimmhammer
Better than I had expected.
Reviewed in Canada on March 9, 2021Color: MA410M ARGBStyle: 4 HeatPipesVerified Purchase
Desire
Top levering
Reviewed in Belgium on February 6, 2023Color: MA410M ARGBStyle: 4 HeatPipesVerified Purchase
Wilson Ang
Missing cable
Reviewed in Singapore on February 4, 2024Color: MA410M ARGBStyle: 4 HeatPipesVerified Purchase
mohammed
looks great and works well, installation can be a bit of an issue
Reviewed in the United Kingdom on March 11, 2021Color: MA410M ARGBStyle: 4 HeatPipesVerified Purchase
